Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
I'm trying to programmate a simple blinkind led project to a custom board with a nRF51822 I did. I'm using a stm32 discovery to connect the custom board throw the SWD port...
I'm trying to update my beacon to use 8.0.0 SoftDevice 110. I've downloaded the 8.0.0 precompiled softdevice hex and loaded the Keil dfu_dual_bank_ble_s110_pca10028 project...
Hello,
I'm trying to use the APP_TIMER API to have tempo, but I've noticed a problem of accuracy when using the RTC1.
I use 0 as prescaler, so the RTC1 runs at 32768Hz...
Hello,
My question based on case, I've experienced recently.
nRF device that could advertise in general mode for limited time by pressing on button and continuously in...
Hello. I am having trouble setting up two PWM channels on nrf51822. The device is running S110 and SDK9.0.
The PWM initialization sequence looks almost identical to the...
Hi,
With reference to This link , I'm trying to make a Nordic solution which can support all beacon applications (iBeacon, Eddystone & Altbeacon).
I'm able to integrate...
Hello I am trying to program this nrf51822 module. I am using J link Cortex M9 . I want burn multilink peripheral in it.
I have followed this link.
I have connected everything...
I would like my device to advertise for 10s and then begin advertising again only on an external interrupt.
What steps are required to restart advertising without restarting...
