I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I'm running out of RAM in my 51822 app and I need to take a look at what's using RW and ZI memory. Very little memory is being allocated with malloc. The rest is allocated...
I am attempting run the rf test from the bootloader. But I have the following problems.
When I try to compile the dtm rf test into the bootloader I run out of space.
...
Hello,
I am using the nRF51822 Development Kit and nRFgo Studio Version 1.17.03211.
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v6.0...
Hello,
I'm starting a new project based on nRF51822 and I'd like to configurate the bluetooth to be appeared and allows the communication managment ( I want to creat two...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi All,
A simple one,, I just downloaded the master control panel app for android in android 4.4 phone.
My question is how to do bonding and how to delete bonding info...
Hi All,
I am testing the functionality of NRF24L01+ and for my purposes I have configured it as PTX, No Auto ACK.
I am able to communicate with the chip just fine and...
I am trying to send continuously sampled analog input using NRF24LE1 using Shock burst,The transmitter is not working while trying sample continuously.please help.
code included...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I'm designing an application where both, BLE and Ant should / could be used. I tried to download the S310 SOFTDEVICE from www.nordicsemi.com/.../nRF51422 . I'm asked...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need a low latency stereo digital streaming device and the model (nRF24Z1) is going to be discontinued.
Has Nordic a replacement for nRF24Z1?
PD: i need stereo, so...
