I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Hello.
I use nrf51822 EK and custom board.
I have to replace the bd address i can not be found in the ble_app_ibeacon_bcs source code.
Is it any way to fix the bd address...
Hi. I'm curious if there's a way to filter devices in the "Discovered Devices" list while scanning with MCP. We have a lot of BLE devices in our office, so the list is fairly...
Hello, I am looking for the way I can use PWM to control duty cycle of connection. I am really novice and my understanding about programming and Bluetooth protocol is really...
I'd like to use the pin sense function as the power switch of my NRF51822 device. That is to say, after the very first power cycle (reset or battery change), the device goes...
Hi everyone,
I am trying to learn nrf51822 using Keil,
I need a very simple program to learn such as:
function bluetoothhandle(value)
{
if(value=="test1")
{
bluetooth_write...
Hi,
I tried to combine BLE HRS & UART together on nrf51822. The service initialization code is
void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;...
Hi,
I am trying to get the PWM example ( github.com/.../nrf51-pwm-library) to work with a Softdevice (S110) that advertises.
There have been several Questions on the...
hi hakon, you told me to do " Try using the variable, for instance by setting "rx_info.rssi = rx_info.rssi;" in the callback and see if that helps." in the question i have...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hi, for some reason ADC_IRQHandler is never called for me.
It's fairly simple and a direct copy of the battery sensor example, so not sure what happened here.
is there...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I am trying to get the proximity example to pair with Windows, but it fails, requesting me to refer to the manufacturer.
I am using gcc in Eclipse on Windows 8.1 desktop...
sd_softdevice_disable before flash_page_erase and flash_word_write ,
after i want set sd_softdevice_enable ,but system is error
how can set sd_softdevice_enable after set...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
My problem with ADC is that I stucked when waiting for event - end of conversion.
I used the code from Nordic...
Hi everybody!
I've plugged my NRF51422 as a slave on a STM32 through a SPI bus. I would like to be able to send to the NRF an unknown amount of data. I also need to read...
