Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
By trial and error, I notice that I can only write 20 bytes to a characteristic, no matter how big I make ble_gatts_attr_t.max_len. A little googling reveals that this is...
Hi,:
I run my application program by nRF51822, about S110 V6.0 and SDK 5.2.
When the program run servial cycle functioin , it is work normail.But sometime, nRF51822 sysytem...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Guys,
I'm about to start my first BLE iOS project and I was wondering if there are any compatibility issues or anything that I should be aware between nRF51822 and...
im running on mac with eclipse and tried to use debugger prints, but the don't show up in the console.
Same goes for printf and uart.
Is there a flag in the makefile preventing...
Hello,
I am checking to see if it is possible to use app_twi_perform() to transmit TWI transactions that have a High Write bit. I have changed the polarity of APP_TWI_WRITE_OP...
I'm developing an embedded application using the nRF52 device. I am using GCC to build the C software and a segger flash device to program the nRF52, all using linux. I wish...
I wrote this code found in an example and it works fine:
#include "nrf_drv_config.h"
#include "nrf_drv_timer.h"
//Before I activated TIMER0, TIMER1 and TIMER2 in nrf_drv_config...
Hi,
I am using eclipse IDE and gdb to debug and flash applications onto nrf52 dk. I wish to be able to print data and messages to the eclipse console. I work on mac OSX...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...
For evaluating the nRF52 for a project I need to demonstrate BLE 4.2. secure pairing with NFC
I want to use two nRF52 eval boards but I need two software examples: One...
