nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hi ,
I am programming nRF51822(s/n 681859006) on my company's custom board, I am using the softdevice (s110_nrf51_8.0.0_softdevice.hex) to program it.
After successful...
Hi!
I'm compiling with 'GNU Tools ARM Embedded 4.9 2015q2/bin/arm-none-eabi-g++' and optimization -O0 and debug level -g3, nRF5 SDK version is nRF5_SDK_11.0.0_89a8197....
Hi,
I developed an application with nordic NRF51822 using SoftDevice S110 8.0.0.
The APP developer for iOS tells me that the app disconnects after about 2 minutes, while...
Dear all
I have a question about using nRFgo studio to Program Application
I have develop a nRF51422 central project for a few month using nRFgo studio.
The nRFgo...
Hi everyone. I'm using nRF51822 and try to work with Eddystone protocol. I use experimental_ble_app_eddystone and my beacon work properly. I validate it via nrf Master control...
Has anyone else encountered a recent problem while compiling projects using mbed online compiler (error message goes "Struct "" has no field "NRFFW" "RF_UICR->NRFFW[0]" in...
I am trying to implement a OTA DFU in my project. The DFU Examples given create a bootloader file of it's own and starts transmitting in the nrf51422 dev kit(DFU_Targ, ble...
Hello,
Platform nRF52 with SDK 11 (S132)
I use nrf_drv_spi_init to register a Handler (used for screen and SD card so it can be long)
I have sometimes crashes when...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
Hi all,
I'm working on mbed os and I cannot use the softdevice_ble_evt_handler_set and SOFTDEVICE_HANDLER_INIT . Every time I build it, I get:
undefined reference to ...
Hi ,
I am using S120 ble_app_multilink_central example. I have configured UART0 in interrupt mode. I send some command and expect some response. It work very well in starting...
