Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I have such code:
static buf[9] = {initializers};
for(i =0;i <9;i++){
while(app_uart_put(buf[i]));
}
I always get "0" before the actual buf content and the...
Hi
I've implemented a peripheral with bonding support by the peer manager. Additionally the device should scan for bonded devices by using a whitelist. I used the function...
Hi,
I'm trying to compare two RC networks by using GPIOTE, PPI, a Timer and the comparator to measure the time needed for a charge and discharge cycle for each of the networks...
Is it possible for one Arduino Uno to have a BLE nRF8001 module and a nRF24L01+ module wired to it (allowing each module to communicate simultaneously)? According to the wiring...
We are trying out the new nRF5x SDK v12 and it looks like the previously working ble_app_hids_mouse example is broken now.
It compiles successfully, but as soon as we try...
I have observed that the Radio Notification from ble_radio_notification.c becomes inverted sometimes. I saw this post about the same problem:
devzone.nordicsemi.com/.....
I would like to use nRF5 SDK for IoT with some functionalities (e.g. SEGGER RTT) from nRF52 SDK. Can I just copy desired modules to my SDK for IoT and suppose it'll work?...
Hello,
For some industrial reasons, I need to store the passkey in the flash of the nRF5 during production and retrieve it at run-time.
I would like to know if there...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
Hi all,
i am using V11 sdk.
i want to send data "hello" in beacon application.
how to add that feature.?
any function calls are there?
-Thanks in advance
Hi,
I am using a PIC microcontroller in my project (18F family) and I would like to know which are the tools needed to begin development with the NRF80001.
I already...
Hello,
I am doing a project using nRF51822, s130 and SDK 11. I have modified the example ble_ap_hrs_rscs_relay.
My problem comes when I try to update a notification...
Hi,
I am porting our application from SDK10 nrf51 to SDK12 nrf52. The application takes use of a serial console accessible over UART.
I notice the new logger module...
Hi all,
i am V11 sdk.
Task:
i want to send and receive data without connecting the nordic_uart example
i.e ble_uart eg is send and receiving the data when we press...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
