Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hello,
I'm implementing bonding feature on nRF52 with SDK_0.9.2.
I found a tutorial which is devzone.nordicsemi.com/.../ .
I followed this tutorial and then tried to...
I have a sensor HTS221 that I would like to power from an nRF52832 I/O to allow programmatically resetting the sensor. Looking at section 20.4.1 GPIO Electrical Specification...
We have bots (what I'm calling our device for this question) that play both the peripheral and central role depending on their context (not unlike the relay example; except...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
HI,
Currently I try to run example/iot/tcp/client in nrf51 iot sdk on nrf51-dk board. Then on server side, I use "ping6" command to test the data sending and receiving...
Hi, Very happy to note that you are planning to release source for nRF Connect for Desktop soon. Do you have an updated timeline on that?
Also, I am trying to use pc-ble...
Noticed this for gcc with -0s optimization an application fail to save a bonding data. It is caused by byte alignment of
static uint8_t buffer_memory[(n_blocks) * (block_size...
Hello everybody,
I am a newbie, and I tried to follow this tutorial to set up my laptop for development.
Everything works until I went to the step "Import existing Eclipse...
Hi,
I am currently writing the firmware of one of our products that will be produced in mass market, and now my goal is to have a unique BLE device name for every sample...
I am trying to study the docs for GPIOTE in SDK12 and see various sections for GPIOTE. What are the differences between: Driver , Abstraction , Handler and Handling Library...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
