Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
I'm trying to compile an application that uses app_error.h, but IAR is throwing an error each time app_error.h is included, saying that the use of the NRF_LOG macro on lines...
Hi,
In examples of SDK 11.0, I see two different defines PSTORAGE_DATA_END_ADDR .
#define PSTORAGE_DATA_END_ADDR ((PSTORAGE_FLASH_PAGE_END - 1) * PSTORAGE_FLASH_PAGE_SIZE...
Hi,
Can you please explain to me what bonding consists of ?
Because i want to use it in DFU from an app. I see an app where we can from the it do DFU . in Fact, the...
Hi there,
Thanks to the great tutorial from Vidar, I can play with the blinky example in Eclipse on Mac. Now I want to try the other examples, and encountered the "Error...
Dear all,
I need to know in detail the nRF51822 RF capabilities asked by bluetooth SIG.
Items 1 to 12 in chapter 1.3
See attached document RF ICS 4 1 0 (002).pdf
Thank...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
Base project: ble_app_hrs_s110_with_dfu_pca10028
Project Device: nRF51922_xxAB
Project...
Hi All,
I am trying to develop a application using radio communication, so i choosed to develop a application so it can able to tx and rx. So i integrated both rx and tx...
Hi All,
We are trying find a way to upgrade nrf51822 in the field post initial release.
I read the following posts
( devzone.nordicsemi.com/.../)
( developer.nordicsemi...
My board requires P0.9 and P0.10 to operate as GPIO pins. On the NRF52 these pins share the function with the NFC antenna. How do I make them function as GPIO pins?
I know...
Hi,
I just finished compiling my code for the nrf51 to take ADC measurements and send the hex values over ble tuart o my iphone. Now I want to see if I can send that data...
Hi, i know maybe this question was asked before, but i have a particulary issue.
I have 2 devices connected through BLE. Just when them get connected i need to send a byte...
Hello!
I need to read a string from UART, there's code below:
unsigned char GetChar(void)
{
while(!RI)
;
RI = 0;
return SBUF;
}
int Readfstr(void)
{
char...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Bootloader: dfu_dual_bank_ble_s110_pca10028 with the device set to nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
DFU Tool...