Can you please help to suggest how to get hci logs in channel sounding examples? Like my use case is that I want to know which commands are going from host to controller and...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
NCS -> 2.9.2 Hi, guys
This will be little bit big of a ticket.
So I recently started working with nrf9160, and I have not much dabble with M33 core as well.
But anyways...
Hi,
I have been testing out the channel sounding feature on the NRF54L15. Each device has a bias (difference between the readings and the actual distance) and I was trying...
Is there any way of instructing the BDS plug-in which optional characteristics to include in code generation for adopted services without converting to a custom service? ...
(/attachment/41972e0db37f912bba4731a3b5ffe839)(/attachment/0838bef738e72c89e2a9af90d6e3f640)(/attachment/a62ce68db8c9d23b285a9f94a5c9beac)I have been developing on the nRF51...
what should be the direction of pin P0.26 and P0.27 when external low frequency crystal is connected ???
or they should be left untouched in the code ???
To reduce the...
Hi:
I come across a problem when I debug NRF51822. I don't know how to config its clock.My board XTAL is 16MHz, and I want config is to 32MHz，Is the method below OK?
NRF_CLOCK...
Hi,
My settings are:
NRF_DRV_SPI_FREQ_1M, NRF_DRV_SPI_MODE_2, NRF_DRV_SPI_BIT_ORDER_MSB_FIRST.
I'm trying to readback 0xD8. The proper value should be 0x71. Instead...
Hi,
I am trying to use the nrf52 in serialized mode, where I was successfully able to program the connectivity board (using SDK 11.0.0) However if I try to load any of the...
We are using a module which has nrf51822 on it. Before we have programmed it, we were able to see it when we scan for ble.
But after we program we could not able to detect...
I am building an automated test stand for programming our production devices. After programming, I need to pin-reset the device to leave debug mode so I can get an accurate...
We have an BLE application that we are targeting the nRF52 device for. The application demands using a UART interface to communicate to a host processor. In addition, we typically...
Hi all,
until now, I used nRF51 Chips on my board. I programed them trough the nRF51DK(PCA10028). But now I would like to work with nRF52832 Chip. I have a nRF52DK(PCA10040...
hi ..
i am new to mbed and nrf51.
softdevice is s130
if i enable the ADC in my project then other output(out3,4,5,6) is not working ok.
if ADC is not enabled then...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi
I have a problem when bootloading with nrf toolbox. It seems like when i flash files over 0x10000 in size the program overwrites itself. When i flash files with smaller...
I know this is somewhat "how long is a piece of string". I'm happy for guidance rather than solid numbers:
I'm trying to spec a "keep alive" circuit for an nRF51822 project...
