NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
Hi,
We are developing a product using the nrf 51422 where the power source is a 3 phase generator.
We rectify and charge on a supercap where the uProc is being supplied...
Please correct me if I'm wrong but my understanding is that unused RAM banks can be disabled to reduce quiescent current.
My first question is what is the current consumption...
Hi,
I'm using RTT debugging with soft-device " https://devzone.nordicsemi.com/tutorials/6/debugging-with-real-time-terminal/ " , I'm able to print few messages, after which...
Hi~ I'm sorry because it usually does not use English writing in English, So there may be errors in English please forgive me.
Last year, I bought some nRF51 Development...
Short: Working Timer. Working SPI. SPI does not work when triggered by timer_handler.
Hello,
I am currently trying to replace delays with timer in my code...
I set...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I want to make nRF51 goes sleep mode.
So I tested linked source code as below.
github.com/.../main.c
It works well.
But...
Hello, Nordic Stuff.
I've been working at ble peripheral devices using S110.
I am just wondering why the sd_ble_gap_disconnect function accepts only the reason code...
I am interested in developing an nRF51822 application for an old PCA10001 nRF51 evaluation kit using a Mac OS X platform. I've downloaded and installed the following tools...
Hello,
I have a nRF51DK.
I am trying to use the TWI driver to communicate via I2C with an accelerometer MMA8452Q.
I already have a working code based on several SDK examples...
How much additional current does enabling the FPU add to the nRF52 processor? I reviewed the Product Spec. but I can't seem to find this listed anywhere.
Thanks
We successfully used the pofcon on a 51822 based design using S110 ver 7 to indicate a low batter condition to the user. However, we are moving to 52832 (currently QFAA-BA0...
