Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hi,
We have updated our code to the last sdk version (nRF51_SDK_9.0.0_2e23562) and we cannot upload the application code anymore with the nRF Toolbox on our iPad. However...
Hi there, I'm having some truble to understand how to set a synthetice 32khz clock from the 16Mhz external crystal. Right now I have the next code working fine:
NRF_CLOCK...
Hey guys,
I’m trying to send a single non-connectable beacon every few minutes in the lowest power way possible. nRF51822, SD S110 8.0, SDK 9-2. Different scenario from...
I am experiencing a fault at sd_flash_page_erase() in the sdk_nrf51 ble examples.
Softdevice 8.0.0 is loaded and is from the sdk_nrf51 bundle.
Both the ble_app_proximity_s110_pca10028...
Here is my power consumption (3.0V):
no app_pwm: 0.010mA
after app_pwm_init(): 0.295mA
after app_pwm_enable(): 0.891mA
If I do app_pwm_uninit(), power consumption...
NRF52 on-site training for today, know BLE pairing use OOB way will be a little bit more simple and safe, and then want to ask next, on NRF51822 platform have the corresponding...
I'm using a dev board based on the nRF52832.
The majority of the time the RSSIsample register returns the correct value.
However sometimes the value returned is 0x7F...
The Product Specification makes it clear that the given levels of accuracy for ADC measurements are only possible when using an external crystal for the HFCLK. We have one...
Hi Nordic,
Running a gdb session on nRF51, it is difficult to debug the code beyond the SoftDevice initialization. Then, I have to step through with (gdb)ni, but this is...
Hello everybody,
I used to my PCA10028 DK board with nRF51-DK-mbed-IF but I wanted to revert for nRF51-DK-J-Link-IF. According to the nRF51-DK - User Guide v1_0 documentation...
I have the code below initializing TIMER1 and and IRQ every 1ms. I call app_sched_event_put within the timer and I get a Hardfault.
Any hints on what is going on ?
Thanks...
I just bought a nRF5-DK and I couldn't get it to work flashing other nrf51822s. The modules I'm using are these wireless-tag.com/.../nrf51822-02.aspx
Here's literally what...
