Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
The CoAP block example has a "put" function, which works just as the instructions describe. It would be helpful if you could also show an example of the "get" function. These...
hello!
Is IoT softDevice for nRF51 DK has all the features of BLE 4.2??
I know IPSP is the feature of BLE 4.2, but i wondered whether privacy and data packet extension...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi All,
I'm using Nordic UART App to write 'A' to TX characterstic and then i expect some action after that as per my code on BLE nordic device, which is happening.
But...
I'm using the attached proximity_setup.xml ( proximity_setup.xml ).
I'm trying to use the Battery Service to send Battery Level notification.
I added the following code...
Hi,
I have just received a nRF52832 Preview DK and I am trying to set it up according to the description in the nRF52 Series - Get Started section.
I have connected the...
Hi All,
I am using nRF51422DK with SDK 10 and trying to communicate with an external peripheral over UART at every timer interrupt.
I have modified the ble_app_hrs example...
Hi All -
Is there anyone successfully able to autoconnect with nrf51822 with a phone/pc/tablet? I have been trying it for the past week and couldn't get my nRF51822 autoconnect...
I successfully turned off bluetooth radio using NRF_RADIO->TASKS_DISABLE = 1 when i do advertise_start(); after certain delay i coudnt connect back for data transfer
Based on nRF51822\Board\pca10001\ble\ble_app_hrs example,
How nRF51822 detect ADC input? Which ADC pin?
Configuration code:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit <<...
Hi, I'm having a problem with calling pstorage_register(); The first I call pstorage_register() is just fine, but the second I call return the nrf_invalid_param.Here is the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
Hello,
I have been trying to use the nRF52 preview DK board as a master device with another chip as its slave device. Now I know that to read or write the function used...
The statements
NRF_PPI->TASKS_CHG[n].DIS = 1, and
sd_ppi_group_task_disable(n)
cause a hardfault when NRF_UICR->CLENR0 is set to the start of the application code, but...
