NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
I run step by step the example of adding DFU to ble_hrs, everithing runs fine.
I try to change in the same way another example, ble_app_proximity.
The problem is that...
Hello everyone
i have created one custom service and i succed to compiled then i checked my service via master control panel it is showing unknown service but i named it...
Hello,
I have a question about including multiple identical services in GATT table. For example, my device has 2 batteries so I need 2 battery services (with same UUIDs...
Hello,
I am developing a NRF51-based peripheral (S110) device with N tactile switches - each one assigned to single "bonding slot". I need the peripheral to be able to...
i have use nrf51822
when no connection creat between android nrfUart app and backon kit so autometically sleep in 180 seconds,
but i have need sleep condition in connected...
I'm new to the Nordic range of devices and the SDK.
I have a project where I'm using the HAL in the SDK to configure GPIO/GPIOTE and the UARTE0. With both the GPIOTE and...
Just want to check that my understanding is correct:
I have ported/migrated my app from SDK 6 to SDK 9, merely because I want to use the DFU facility. However, I have read...
Hello everyone
i am trying to add printf statements inorder to see the excution of the program can anyone sugges tme how to printf statemtns in app_uart example!? i would...
Is there a document describing the interaction and any asynchronous issues with the different types of event handlers? As I read it there are softdevice events, BLE events...
