I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I have a nrf51 dongle and I try to connect my Android smartphone to it. My smartphone is BLE compatible, so no problems here.
I flash the firmware using master control...
I am a newer for Nordic's BLE.
and has WaveTek nRF51822 BLE Shield (design for Nordic), and downloaded the S110 softdevice version 7.3.0 and the wavetek_connectivity _s110v1...
Hi
I have some problem about the HomeKit SDK,is there anyone could help me?
In the HomeKit SDK,such as lightbulb project,there is a function mfi_i2c_configure that...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
[test result] change to use Timer1 of timer example,it failed. if you use timer0, it is OK..
SDK IS 9.0:
nRF51_SDK_9.0.0_2e23562\examples\peripheral\timer
[test step...
Is there a way to access the lower level clock which a connected slave uses to stay in sync with the master. We want to use this to keep our PWM in sync. We are looking for...
Hello,
After looking into forum regarding usage of S130 stack for using the device as both central and peripheral, I understood that the peripheral and central can concurrently...
Hi All,
I have query regarding PWM usage in nRF51-DK. I have a requirement to control 3 LEDs (brightness and power) simulatneously. I intend to use PWM for the same. But...
Hi there! An error occurred in device manger. It was caught at the first APP_ERROR_CHECK in device_manager_evt_handler. Error code is 0x88. I can't find this error code in...
Hello,
I do not see the bootloader files for this example in SDK 0.9.2. Where can I find the boot sequence for the ble_app_hrs example, and in what files is the boot setup...
Hi,
I don't see in SDK 0.9.x any examples pertaining to accelerometer peripherals. I see a TWI sensor example from the nRF51, but I am working with the nRF52. Are there...
The nrf8001 datasheet seems to mention that there should be no connections when sleep command is sent. So I wanted to call aci_disconnect first. But what reason do I use?...
