I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I recently grabbed the latest SDK nRF5_SDK_11.0.0-2.alpha. I was looking at some of the changes and wanted to run one or two demos to make sure I was able to build them properly...
I am testing this on ble_app_hrs and ble_app_hrs_c. After devices are bound I would like to skip discovery as it takes long time. So all I need to do is get the service's...
After I receive data by ble_nuts,using example ble_app_uart.
I call ble_nus_string_send to the central, however I got error,I print error code is 8 which means "NRF_ERROR_INVALID_STATE...
hi
First,I apology for my poor English...
I want to make a project to connect 2 device.
With a sensor from TI , which comes out the sensed signal .
Transfer the data...
Hi,
platform info:
SDK 9.0, NRF51822, SD:s110_nrf51_8.0.0, Master Control Panel(android):2.0.0
We use eample dual_bank_ble_s110 under dfu/bootaloader/pca10028/ of SDK...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
