hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hi,
I designed before my board for 2 layer PCB and i used the coplanar waveguide with ground-plane in the bottom. now i want to move to the 4 PCB layer and i choose the...
Hi, I'm porting my project from SDK8.1 to SDK10.
I replace static app_timer_id_t m_beacon_timer_id; to APP_TIMER_DEF(m_beacon_timer_id);
to avoid hardfault when creat...
Hi all:
I modified DFU-BLE to make it suitable for S130 on nRF51822. I made the following modifications:
On "dfu-ctr1_pt_add"
ble_gatts_attr_md_t cccd_md;
memset...
Hello!
Until now I am using a nRF24L01 with johanson balun (2450BM14A0002) and MIFA.
I want to add a power amplifier to my nRF24L01 project. Can anyone give me advice which...
Hi
I have a programming issue with nRF51822. I am using the nrfjprog.dll to program this microcontroller in my test equipment via J-link Plus. When I have programmed a...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
Is the advertising interval between two packets P1 and P2 defined as:
Interval = P2_start - P1_stop (time between packets)
or
Interval = P2_start - P1_start (time...
In a project I worked on using softdevice s110 v. 7.1.0, if the receiver hadn't enabled notifications, sd_ble_gatts_hvx would return an error, so I used the following construct...
Hi,
I want to advertise multiple UUIDs, one after another
Do I have to stop advertising, or is there a way, that I can update the struct in the background?
Currently...
