Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
We are a small start-up developing low volume product and paying 2500 USD to Bluetooth SIG for listing our BLE device in their EPL is too expensive for us. Is there any option...
I'm looking for a way to let my device "nrf51822" to be connected only to my own mobile app.
I'm wondring if you have already a Nordic solution that I can use ? (tutorial...
Hello friends,
I'm having MDBT40 EVB which is cheap one as compare to other but with lack of build and debug support. But i dont know how do i flash my hello world blinky...
developer.nordicsemi.com/.../a00935.html
The doc seems to provide only write functions.
And, the flashwrite example doesn't show how to read from flash even after device...
Hello,
I am currently looking through my error handling and noticed that there are some errors that I do not really understand fully, so I've summarized them here:
0xDEADBEEF...
Hi,
I am trying to make a communication between a nRF51(uESB) and a nRF24(ESB). The uESB uses tx_payload and rx_payload as buffer to send data. Bytes 0 to 4 are used for...
Dear Nordic team,
I've seen very much reproducible crashes of your Android nRF Master Control Panel app when trying to see details (button "MORE") of particular Peripheral...
Hi Nordic,
Is there a way to follow blog posts the same way as standard questions? I haven't found anything and it's really painful when you want to follow discussion or...
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware:
• nRF51822 Evaluation Kit (PCA10001) and a mini USB cable...
hi, i am a beginer in BEL application.
after some tries, i can compile and download 'ble_app_uart'.
but the module does not work at all also it dosen't advertising....
...
i make a new "Makefile! project" using example in SDK first i use the "blinky" ,
it looking likes can be work, then i try to use " blr_app_hrs_c " ,
i do the same step to...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
