Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I have a few characteristics under a service, and I'm trying to store the value if any of these characteristics is written to. However I run into an issue where if I enable...
Hi !
There is one thing I don't understand with the led included on the NRF51-DK board.
According to this thread ( devzone.nordicsemi.com/.../ and the datasheet it seems...
I want to take saadc samples for one second,every 5 seconds,the rest of the time the mcu is in system on sleep mode with rtc1 on.Eery 5 second there is an rtc event and the...
As the datasheet showing
The GPIOTE input mode consumpt upto 22uA ,it is inconceivable.I want use NRF51822 to design a ultra low power consumption production ,and use...
HI:
I want to use nRF24L01+ as TX, and nRF51 Dongle as RX. And I try to use nRF51 Dongle to just listen for the RSSI of the NRF24L01+. Is there any example or reference...
Hi, I am new to nRF51DK. I am following this tutorial shown below:
developer.nordicsemi.com/.../a00066.html
After I flash my s130 softdevice, I follow the file directories...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
Hi, i am designing a board using balun in it. Also, i am going to use meander antenna of nordic dongle(reference image is attached). As i can see, there is no RF coplaner...
Hello , I want know , if i used the Gazell Pairing Library (gzp) , it means that I can not use the ACK
Payload function ？if i can use the ack payload function place give...
Hi,
after reading the NFC with an smartphone the power consumption stays very high without doing anything else...
I don't know if this is related to this bug: "NFCT...
Hi,
I saw in the infocenter that the SAADC can measure the VDD directly. So in my case I want to check the voltage of a 3.3v coin cell regularly, I could do this without...
Hi Everyone,
The On Semi 7150SL reference design incorporates a dongle that can stream stereo music to two hearing aids which are equipped with the Ezairo 7150 module....
Dear sir,
Can we use NRF51822 OR NRF52832 as a slave device .As our controller is STM32F407ZET6 and we did not want to change any firmware from our previous version except...
