Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
I want connect with password with my nrf52832 via Android phone. How I can do it? I do not want to do pairing how in example project "ble_app_gls". I used Android 6, SDK14...
we have used the ble mesh sdk v0.9.2 to implement long range ble mesh network on nrf52840 SOC
it is successfully working with s132 softdevice. with default configuration...
Hello,
I'm trying to switch from softdevice s332 v2 to s332 v5 (tried also v4), but I get this error: "region RAM overflowed with stack".
I'm guessing the problem is in...
Hello! I am testing project "ble_nfc_pairing_reference". When my NFC device touch the NFC antenna on the device screen is written: pairing; connecting; could not connect....
Hello,
I have an nRF52 DK, running S132, as a client. After scanning and connecting, I use ble_db_discovery_start, which finds the devices of interest, connects, and finds...
As the title specifies, on writing to the registers mentioned, I receive a Fatal error.
Here's the test code
void save_ram()
{
__DSB();
NRF_POWER->RAM[0].POWERSET...
Hi,
I would like to know if anyone ever tried to alter the SEGGER J-Link OB Code that goes on the ATSAM3U2CA-AU IC (this is the IC that controls de PCA10040).
I'm asking...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 4 work...
I asked about if NRF52 can pair to eachother without a PN532, but sounds like no, it can only read RFID tags.
So, how about if at factory we make RFID sticker/tag that...
Hi,
I need 32 bit timer-counter with s130 stack. Timer0 is 32 bits, but ble stack uses this timer. So how can i use timer1 or timer2 like 32 bit timer?
Is there any...
Do u have mobile/ios application that allows you to scan for Bluetooth low energy devices with nRF52840 and communicate with them?
If not, how we can do it?
Hi,
I am wondering which is the best method for BLE security to avoid MITM, protect the data (sniffers) and limit connection only to allowed devices for a massive number...
I am now using nrf51822 chip connected to a 50-ohm nominal input/conjugate match balun and then connected to an Embedded antenna.
I am requested to do a radio test which...
