I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi,
I have read the following posts and understand how low clock frequency mode can be selected
devzone.nordicsemi.com/.../
I've also read in many posts that 4s calibration...
Dear Sir:
Could I use the external reference AREF1(pin0.06) instead of internal VBG 1.2V for ADC operation ?
I do the following settings to config using external reference...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
Hello,
I'm trying to write value to a specified address with ble_flash_page_write .
I'm using ble_flash_page_write after ble disconnect event. I've tested different...
hi Ole BAUCK, my slave device is STPM33 ENERGY METER using this device we can calculate vrms,irms,real power,reactive power,energy and many more.. that device is not having...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. Now it almost works. But after an app image has been successfully transferred...
hi all,
i am using sdk v8.
i want to transmit the address through uart and read the data using UART.
i am using app_uart_get and app_uart_put api's.
PROBLEM:
if i connect...
Hi, it says that I have to put my beacon into beacon config mode in order to configure beacon device through the app. How do I enter beacon config mode in my nRF51dk? When...
Hi, In my project I need to measure current values for every sec and update those values to advertising data. So, I take manufacture field in advertising data to update the...
My set Up: Nexus 6 (Android version 6.0) as Peripheral, Nordic as Central.
I want to achieve ble pairing using 'pass key confirmation' methodology.
The nordic device has...
Hi Nordic Developers..
I am using nrf52 with softdevice 132.
In my project i am using external EEPROM(Microchip 11AA010) that uses UNI/O protocol and Single I/O Serial...
I'm using SDK 8.1.0 (SoftDevice 7). I built a version of dual_bank_ble_s110. Installed both on a freshly erased pca10028. It comes up fine and sets the LED on. It's advertising...
