Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello Nordic! My application requires an nRF51822 using S110 to handle both Notifications and Indications over the same characteristic.
The CCCD value 0x01 = 0b01 enables...
Hi,
In order to start my own board with nRF52 component throught SWD, I think I've to use Segger Jlink. I expect to buy the basic version, that sound good for me, but I...
Hi,
I have some problems with bootloader debugging by using app_trace_log().
My board is pca10028, and I use the SDK 10.0.0 for it. The Keil version is v5.20 and Jlink...
Hello All,
How to interface nRF905 with nRF51DK board?
Any driver is available for nRF905 which support nRF51.
Any help will be appreciated.
Regards,
Rajneesh
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
Hi
what is the best way to implement a sleep after disconnect?
We are using a custom board and I implemented it this way:
on connect : turn advertisement off
on disconnect...
I used iar for my project. But for some reason I have to transfer my project to keil now. Attached is the icf file from iar and I also attached my keil settings. Now the system...
In following the example for a DFU BLE upgrade I have configured the following system
on an nRF52 DK install the softdevice and bootloader:
nrfjprog --family nRF52...
In my code, I have some 'print'-style functions that write data to a buffer, and that buffer then goes to the Nordic UART implementation. This is user code, and I don't know...
Hi, I'm trying to adapt the stm32f4 library from:
link text
to run an nrf24l01+ with an stm32f373. After some initial SPI headaches, a lot is working. In the initialisation...
I want to confirm how much current is being drawn from the battery while the nRF52 is in it's absolute lowest power state and waiting for an NFC field to wake it up. From...
I am interested in setting the tx power level the advertising packets in a nRF52832 are transmitted with. I saw there is the TXPOWER register in the RADIO section (address...
I have a use case where sensors on a BLE peripheral need to push notifications to a BLE central indeterministically. So it needs to keep the connection always on. The notification...
