We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello all,
I am trying to make use of some Adafruit libraries for some sensors in my nrF52pca10040, the libraries are these two Adafruit_BME280.cpp , Adafruit_BME280.h...
Hello
In a schematic I saw the "SWO" connection appear on the Programming/Debug connector beside SWDIO and SWDCLK.
What's it for?
Of course it means "Single Wire...
I want to increase ble_app_uart_pca10040 app sample rate.
I have my own board with microcontroller and use nrf52832 as uart to ble.
I made pack length to 20bytes, I have...
When I start program, my program fall down to
__WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info)
{
NRF_LOG_ERROR("Fatal\r\n");
NRF_LOG_FINAL_FLUSH...
Hi
While using 2 nRF51422 dev boards and using the DTM software together with the DTM python example script the python program reports 0% PER even if I cut the antenna...
Hello,
I am using SoftDevice V4.0.3 and nRF52832.
In this code snipet I got the error code 2 when trying to enable SoftDevice :
int main (void)
{
ret_code_t err_code;...
Hi y'all
after having successfully created my own service, similar to the Uart service, I'm now trying to implement security.
As far as I understood, best practice is...
Hi.
I loaded the ble app uart demo and added some bits of code to read some i2c sensors.
I also added a buzzer which buzzes on powerup (simple for loop).
I would leave...
I'd like to (re)set my characteristic's value to Zero. (after my services and characteristics are set)
I tried to search methods that can set value of characteristic when...
Hello,
is it possible to use the RSSI value of the NRF51822 for collision avoidance?
How long does an RSSI measurement take?
I'm trying to implement a discovery protocol...
Hi all! I used PWM module of nRF52832 to create the PWM but i don't know how to update new value to duty_cycle. This is my code. I used Button (Pin 13) to set a new DUTY_CYCLE...
I am trying to set custom value to advertising address. The code snippet is below. I am getting error code 0x10.
static ble_gap_addr_t * p_addr;
uint8_t itr_i;
p_addr...
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
