Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
I want to use the nRF52832 as native transceiver 2.4GHz and I'm looking at examples of the latest SDK.
I'm using Segger Embedded Studio.
I found some examples...
Hi, I'm on final development stage of my custom board. I'm using nRF52840 with nRF5 SDK v15.0.0 and S140 SoftDevice v6.0.0. I need to trace the over-the-air communication...
I'm not using a softdevice, and am doing some time critical measurements when the radio begins transmitting.
This code works very well with nrf51:
__disable_irq(); NRF_RADIO...
Hello
I have a question i cannot figure out. I'm using my phone to send string on my NUS client (NRF52 with SDK15.3.0 and FreeRTOS) and the event BLE_NUS_EVT_RX_DATA is...
Hi,
I am new to development with Nordic chips. I am using nRF52840-DK (SES,nRF5_SDK_15.3.0_59ac345) to read analog input on ADC pin AIN0. I want to continuously read the...
Hi,
I used a NRF52832 to test our product with Python Script.
I enable my notification. I start to receive notification and I have a crash after received first notification...
I've used the DFU bootloader from SDK 14, s132 and the ble app uart example as a boilerplate for my app.
Now i'm looking into making some relatively large changes to the...
Hi,
I have problem compiling "HTTP application update" sample form the SDK for the NRF9160. I am using all the latest tools: * segger embedded studio: v4.18 * nrf SDK v1...
Hello,
I had problems connecting the periphery to the central. When I connect them, I get notifications like this from peripheral, but after this message they don't lose...
Hi,
We are using nrf52 dev boards running mynewt and until two days ago we could use the app to identify/provision and get composition data for nodes and get composition...
We are in the final throws of testing our boards that are based on the BLE UART Peripheral application. The current test environment involves monitoring board and battery...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
