Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I tried with the DK and my own USB-serial adapter and both fails at 1M with HWFC with this error:
nrfutil dfu serial -pkg bltest.zip --baud-rate 1000000 --flow-control 1...
Hi I would like to interface the nrf9160 with amw136 (silicon labs) module wifi.
The amw136 has the interfaces: serial (UART, remote terminal), SoftAP and WLAN client (concurrent...
i am working on nrf52832 DK, i am trying to upgrade my development kit firmware using mobile
and i successfully build "secure_bootloader_ble_s132_pca10040.hex " application...
I'm currently using this setup on a fitness device prototype that will send battery status, scores and relevant infos. RPi >>>RFM69 915MHz )))))) ((((( RFM69 >>> Adafruit...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
Hi, environment is nRF5_SDK_16.0.0_98a08e2 windows SES target is nrf52840. I am using the nordic dev board. The final product is a wearable, which will connect to a smartphone...
Hi All,
I'm using NRF52832 for our product. I test bootloader functionalities with development kit. The software system is also tested separately by directly programming...
Is it possible to achieve 2Mbps real speed when sending 2Mbs of data in BLE.50?
It supports USB 2.0 H / W, but the actual speed is full speed. Is high speed possible with...
What is the need for a provisioner? Is it mandatory to have provisioner while client and server communication? In which condition provisioner needed in mesh network? Which...
Hello,
This is more a question than a issue. I am working on a sample to transmit data from MOSI of the SPI to UDP. It is possible to see received data through SPI on LTE...
I would like to make a timer to check the GPIO status.
The current code is like below:
I already checked that timer function is worked by implant the specific event...
Hi, I am developing sensor reading via ble using nRF52 Development Kit from scratch.
Since bluetooth, nrf, sdk stuff are a whole new world for me, I m following step by...
