Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello Nordic team,
I am trying to get my product read for FCC/CE compliance testing. I came across the radio_test example and other examples posted on DevZone. I have the...
Hi,
I have just recently started to develop an NRF52832 chip with Keil uVision 5.
My setup is the following:
PCA10028 Development kit connected to Feather NRF52832 bluefruit...
Hi,
We are planning to add an external flash to our nrf52840 based design.
The flash type is
http://www.puyasemi.com/uploadfiles/2019/06/20190604154800480.pdf
I'd...
I used This char tutorial for this project. Basicly I added beacon advertising mod with a connection mode to this project and I tried to changed minor and major of the device...
Hello! Something strange is happening with my nrf51822.
I have a simple code to obtain data from the ADC and send it through BLE.
I do the following in the main loop:...
Hi,
I am new to Nordic Thingy91.
I have tried to connect Nordic Thingy91 (nRF9160) device using "nRF connect v3.2.0", via USB. But I am facing, below issue.
Issue 1...
Hi,
I am getting the same error despite adding the files properly.I even tried by providing the absolute path.
"nrf_section_iter.h": No such file or directory.
I get errors saying XYZ.h header file is not included though I have included them everywhere. Please help me on how to resolve them.
Regards,
S Sachin Goud
Im use the \nRFready Smart Remote 3 nRF52 v1.2.1alpha\nRF5x SDK-SR3\examples\ble_peripheral\smart_remote_3_nrf52\Projects\Firmware_nRF52832 code ,then I have dowmload the...
Hello -
This is a strange problem and I'm guessing I am missing something obvious. I am using the sd_ble_gap_scan_start() API to perform active scanning as follows:
...
Sdk: nRF5_SDK_15.3.0_59ac345
example: nRF5_SDK_15.3.0_59ac345.s.ble_peripheral\ble_app_hids_keyboard
question: After connecting to ios, ios virtual keyboard is automatically...
In some other non-hid app, I can set APP_ADV_TIMEOUT_IN_SECONDS to zero and it worked fine. The advertising is continuous.
But in the ble_app_hids_mouse, I set both APP_ADV_FAST_DURATION...
I would like to use AT commands to get the IMEI on a custom board that has an nRF9160.
In preparation for this I am attempting to get AT communication working on a NRF9160dk...
On the nRF52811 with the s140 softdevice, what is the set of things to do to enter very low power sleep state? The product specification says ION_RAMON_RTC is 1.5 μA. What...
