I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
I recently purchased the nRF5340 PDK. I am working through the getting started guide and can't seem to get the Heart Rate Monitor demo application working.
Firstly, when...
trying to get nrfutil working on ubuntu, following this guide:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html
after...
hi, I have used to segger j link basic with nrf connect programmer to program mass production.
but, It takes 30 seconds. For better efficiency, can It be improved to change...
Hi Everyone,
I need to develop a bootloader and a firmware update procedure.
My development environment is nRF52840, sdk 15.3.
Program download configuration 1) Download...
Using Mesh SDK 3.2.0.
The returned Device Composition Data is malformed when requesting it after the node has been reset. This is because the sig_model_count and vendor_model_count...
Hi to all,
i am trying to develop an app with NRF52840 soc and nordic sdk 15.03. in my app i implemented a usb hid device and also i am using flash storage at same time...
Hi
After getting SDK16 , we have tried to load a combined hex file with bootloader + S132 V7 + application with dfu + bootloader setting page to PCA10040. And It work well...
Hi,
i am working with aws-fota example, i copied my certificate to certificate.h file, once i run the program it shows like
The MQTT AWS Jobs FOTA Sample nrf_inbuilt_key_delete...
Hello, I started to delvelop an program from mqtt simple, now that I almost finished I saw that mqtt is refusing to connect to my broker, I deleted all my code I wrote and...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...
