I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi. I would like to know is there a possibility for creating repository for nRF5_SDK_16.0.0? Just like it is done with nRF5-SDK-for-Mesh, a clone of release files. I would...
Good morning everyone,
we have developed a custom board featuring the NRF52840. The device works fine, but I am having a hard time in making the USBD work.
I took most...
Hi
I am working with a Nordic nrf52840dk using segge and sdk 16.
I am using the nordic UART example in examples/peripheral/uart.
The issue I am having is that my data...
Hi
I try the example from here for a DFU OTA: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v3.1.0%2Fmd_doc_libraries_dfu_dfu_quick_start...
Hi,
I have a nrf 52840 DK with me. I have downloaded the SDK for the mesh(v.3.2.0) and SDK (v 15.3). I am using segger embedded studio here. I have modified SDK_ROOT location...
The replies aren't showing in my original post and I can't add replies to it for some reason.
https://devzone.nordicsemi.com/f/nordic-q-a/55304/sdk15-3-0-sd6-1-1-ll_length_req...
Hi,
I developing a application with the nfr52840 board with SDK 15.2. i have started form the ble_app_cscs example for development my code. I I would like to send packet...
Segger Embedded Studio seems to use the full path of the FILE for the __FILE__ macro. During development this can skew the size of the final image if there are lots of trace...
I am working on a ZigBee coordinator device that will collect data from various sensors in the network and forward them to a gateway. I have started with the CLI example and...
We have custom board based on nrf52840 and using an application based Zephyr RTOS platform.
Sometimes, it is observed bus fault and hardware exception logs are observed...
Hello,
I am really wondering about the design of the UARTE peripheral. The documentation for the nrf_drv_uart and the nrf_serial library is lacking quite a bit. Most of...
Dear Nordic:
My NRF51822 based SDK9.0 can not connect HuaWei mate30 mobile,but it can work for any other mobile with android system.I used nRF master pannel APP downloaded...
Hi!
I'm having trouble getting any response from an NRF52840 MCU on a custom board we've made.
I'm hoping someone will be able to point me in the right direction by detailing...
