Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
On November 19th, I participated in the 2019 Nordic Tech Tour with my colleagues, but some of the content was not clearly understood, especially regarding the development...
Hi all. I want to measure current consumption on nRF52840 DK (PCA10056).
I have the SB40 cut and the 12 Ohm resistor placed in R90. I measure the voltage on this resistor...
Dear team：
How can I use ble-bas-c to change Characteristic UUID or Connect the 1800 service and rename it with the 2A00 feature value The example is \SDK\nRF5_SDK_15.3...
Hi,
I am new to this. I want to build a mesh network using nrf52832. I have already downloaded and gone through nrf5 SDK for mesh but i am confused about what to use to...
I am using nrf51822 DK. How to set GPIO pins as output pins and access the pins to set or reset the output.For example if I want to use pin 20 as output, how to configure...
I am trying to read if an input is 0 or 1 but for some reason it takes the first one its offered and then it does not change anymore.
int main(void)
{
nrf_gpio_cfg_output...
<Environment> - nRF9160 DK v0.8.5 - nrf tag: 1.1.0 - modem version: 1.1.0 - using an external GPS antenna, SW12 => CON
I'm attempting to use udp_gps, but doesn't work out...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
Hello. I am using nRF52832. The SDK version is 14.0.0. UARTE is used for serial communication with other devices. The baud rate is 38400bps, and a maximum of 20 bytes of data...
Hi, I could not find a way to use Segger Studio debugging features when I have a bootloader for DFU functionality. Is there a way to something like that, because when I click...
I am trying to read temperature, pressure, and humidity data from an Adafruit BME280 sensor using the nRF9160 DK. The communication protocol that I am using is I2C and I am...
