Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
I am porting the eMD-6.12 firmware/library by Invensense for the part MPU9250 into the nRF52832. My toolchain is compiling through gcc allowing examples from SDK's to be quickly...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
I am using SDK V15 with an nRF52DK and Keil compiler.
I have difficulty finding an example to use a GPIO to drive a Piezo Buzzer. The requirement is very simple: use a GPIO...
Hello,
Is there anyone successful in communicating with an nRF52 based GATT server from a Windows 10 App? I’ve skimmed through the forum and do not come across any positive...
Hi,
I have an application that verifies a chunk of data and EdDSA Ed25519 signature against a remote public key.
The device application generates a random number, sends...
Hi,
I would like to add some custom sensor for Thingy:91 board. I notice that there are no GPIOs available to connect sensor to nRF9160 SiP? So do I need to connect the...
Hi,
Today I found I was unable to flash my nRF9160 DK. "west flash" fails with the error message "Installed nrfjprog is too old for the device. Please upgrade nrfjprog to...
I am trying to follow the section “Declaring custom cluster” ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v3.0.0%2Fusing_zigbee__z_c_l...
I've tried for two days to log back into the cloud service and just get the spinning angles. I tried to create a new account and the same. I was able to change the password...
Hi all, I would like to implement a fault handler in our nRF9160 based system to handle hard faults/unhandled exceptions by resetting the system, but am having a hard time...
Dear Nordic team,
I have a running NRF52 with a firmware based on the freeRTOS demo. To this demo I added the PDM Support Module and the TWI Module.
As soon as both sensors...
We are trying to implement models inside the mesh. So we've started with a functional example of the generic on off and tried to update it according to our needs.
The custom...
Hi,
I have 3 devices that all act as broadcaster and observer they continuesly sending data to each other, now i want to establish a connection between one of those 3...
