Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
We see that in documentation V1.1 there is this info on a pin added.
"AUX - Single-ended 50 Ω ANT loop-back pin"
What is the function of this pin?
Documentation...
I found several threads with same questions. And also found source codes.
But they are too old and require Legacy support for KEIL and old softdevice.
Is there actual source...
Hi,
The product is peripheral, CPU is nRF52832 and I use nRF5_SDK_15.2.0_9412b96.
My customer asks me how many bonded amounts support in our product?
because I can't...
If I enable the zephyr shell inside my project with the following config; I'm not able to see anything on the UART If I have CONFIG_SERIAL=y in the SPM prj.conf, If i disable...
hello:
I am using ble_central\ble_app_blinky_c example and attempt to be a central scanner to scan and connect to many BLE peripheral nodes.
The name of target BLE peripheral...
Hello.
We are running an application without BLE at this stage. We measure about 20ma at run time also by the datasheet max is 6ma.
We were thinking that because we don...
Hello All,
I purchased nrf9160 DK board for sending text message using AT Commands. I programmed the SIP to accept AT Commands. Using the LTE monitor app, I tried to initialize...
Why Nordic doesn’t consider update of already 5 years old nAN-36 Creating Bluetooth Low Energy Applications Using nRF51822 ?
It is the most meaningful tutorial for starters...
I recently obtained a PPK from Mouser and plugged it in my nRF52DK. I use it to measure current of an external device.
When NRFConnect "connects", it works great. However...
Hi,
I'm using the latest release of software V1.0.0 with the nRF9160 DK and today started flashing the examples.
at_client worked fine (just tried flashing it once, but...
Hello once again Nordic World,
We are preparing code for production, and one of the last issues to resolve is how to "uniquely" connect our ble_app_uart peripheral based...
Hello,
I'm working on NRF52832,using SDK16 Segger Embedded Studio
now the thing when upload APP_NOTIFICATION it works and also discoverable.
but when upload APP_UART...
Hello.
I just found here: https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html
something like this:
"To turn on sensor...
I am trying to trigger my target device (nRF52832) into DFU mode using nRF52832 DK.
According to my approach, I need to send DFU bootloader given in "installed folder:\examples...
