After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT , But PB-ADV still hasn't changed.
...
We are implementing a DFU controller in a microcontroller that communicates with the nRF boot-loader over serial. The target device is nRF52832 using SDKv15.3.0. The boot...
Hello.
I want to see NRF_LOG_DEBUG ("some") through the terminal. When I compile, I get the following error: What should I set or change? MCU : nRF52840 compiler: IAR...
1.I used Nrf52810 and the flash size is 192KB. I now need Master mode and slave mode. The SoftDevice I chose is S132 (S112 slave mode only). I found that S132 (130KB) + Bootloader...
Hi.
I have issue measure ADC value from battery.
setup is NRF52832, SDK 15.3.0, S332, using ANT+, BLE, GPIOTE, PPI, RTC, APPTIMER, LOW_PWM
my goal is measure periodically...
Hi all,
I am struggling measuring time between events. I thought to use the timer driver and the nrf_drv_timer_capture_get function. This is my test code:
I expected...
I am using nRF5_SDK_15.2.0_9412b96, softdevoce 6.1.1, NRF52840, based on ble_app_uart example.
I have a disconnection problem after couple of hours from an android app...
Hi everyone!
I'm using nrf52832 SDK version 15.0 and softdevice S132 V6.0.0. I'm getting an error when trying to program our board:
"Failed to connect to target.
No...
The build environment is a clean install of SEGGER Embedded Studio for ARM Release 3.50 Build 2018081000.36713 Windows x64
The nRF5_SDK_15.2.0_9412b96 version SDK is used...
Hello People,
I am new to this ble mesh concepts, i am evaluating and want to check whether nrf52-mesh-light-switch-client-server-proxy can supports custom service? if so...
Hello,
I just received my NRF52840-DK board today. I was able to run the demo (LED blink/Switch and NFC) which comes factory installed. But copying the hex files from demo...
Hello,
I am trying to migrate to nrfx drivers in my project. Currently using SDK15.2 and nrf52840. I have 2 SPI peripherals in my application. One being an SD card and the...