I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hello,
I tried the basic proprietary rf code that is esb_prx and esb_ptx on the boards and the communication is very fine. The default set of data that is 0x00 to 0xFF is...
Hey! I'm writing a program for communicating the laser sensor pmw 3610 (pixart) with the micro nrf52832. In the sensor datasheet it is said that the time between sending the...
Hi:
I am an engineer from China. Visiting infocentre in China is quite slow. I found some offline documents for nRF5_SDK in https://developer.nordicsemi.com/ and they are...
As the subject description.
I have already test the official sample buttonless_dfu_app and the secure bootloader already. It could work for OTA fucntion.
And my application...
Hello!
I am new to controller programming. My work at the institute is connected with bluetooth research, so I need to learn how to program nrf52840. My microcontroller...
So I looked at the example of the temprature read and I got the following code:
But the problem I got is with the: while (NRF_TEMP->EVENTS_DATARDY == 0), I don't want...
I read the discussion in the following link, but my application is different so I want to ask for advice on how to proceed.
https://devzone.nordicsemi.com/f/nordic-q-a/50642...
Hi all,
I successfully flashed the peripheral_hr sample from the Getting Started guide into my nRF5340 PDK (from here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
Hello ...
Our product (nRF52810, SDK 15.3.0, SD 112 6.1.1) allows the user to change the device name, which typically happens once when new product is received. Our app...
I am running the ADC demo for the 52833-DK (pca10100) and can’t seem to get any valid readings. SDK 16.0: examples\peripheral\saadc
I am applying 1.5V to AIN0 on P8 and...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
