Dear Nordic Engineers
We found a problem on the NRF54H20. When we ran C:\ncs\v3.0.2\nrf\tests\benchmarks\multicore\idle_gpio example, the current tested on the VDDHV of...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
I am following the NaN-36 example... So far all is going well but i am stuck at section 4.5.4 . I have checked over all the directions three or four times... I have to be...
I am hoping someone can point me in the correct direction as I have posted my question on the SIG forum and didn't receive any responses.
With a nRF51422 device is there...
I've followed the instructions for adding the DFU service to my app to the letter and can see the DFU service from the central and can enable notifications on the control...
Hi.
nrf51x22 has 32 IOs. can we assign 2 pin to usb d+, d-, and listen interrupt.
yes, nrf51x22 has uart support, but many host device only have usb port. serial port...
Hi All,
I am using NRF51822 chip pca10001 development board.
I flashed ble_app_hrs application to the board.
I configure 3 channel for PPI.
static void ppi_init...
Hello all,
I'm writing code for the nRF51 to allow it to be driven via the Android ANT SDK (from Dynastream), using standard ANT protocol messages.
However, it's occured...
Hi,
I'm using the nRF51 DK as a BLE sniffer with your Wireshark plugin. I have several BLE peripherals in the same room I'm testing it so it will be useful to filter data...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
Hi,
I want to implement stack tracing to check stack overflow and remaining stack. I followed the implementation given in example github.com/.../memory_watcher.
Memory...
Hi
I am coding a s130 NUS example.
The base example is sdk8.1.0 ble_app_uart peripheral example.
I added central part from Github sdk8.0.0 ble_app_uart_c...
Hi
I've installed the new tools in version 7.5.1 to support the new nRF52 family. While working on the nRF51 again i found out, that the old parameters i used for programming...
Hi,
I'm working on a project where nrf51 modules should communicate with each other. For that i'd need to set characteristic that can store string. Now i've done that ...
