This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs
but:
1.How does the client receive those data?
2.How dose the client send data to server...
I'm totally new to Nordic, ARM development, and the mbed platform. Not new to embedded development however.
So far I can't get the simplest possible program to run.
...
I just received my nrf51822 dev kit and noticed that the SWD debugging cable will only connect to the PCA10004. The PCA10005 that came with my kit has pin 2 missing, rather...
HI,
I wrote my application based on "MasterEmulator->ProximityDemo" for testing device with nrf51822. My device have to switching between Gazell and BLE stacks so all the...
Hi
In ble uart project, the data is used string format. Now, we want to modify uart apps to tx/rx binary format. Could you tell us how to modify the uart apps? Thanks.
...
I added a local service with a characteristic with the Notify permission set.
On the device I'm connecting from to the nRF8001, I can see my custom characteristic has a 0x2902...
I'm designing what is essentially a small beacon board built around an nRF51822. On the antenna outputs I've used the discrete component balanced to unbalanced circuit shows...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
