Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
i have bluetooth usb 4.0 dongle..which part of bluetooth stack it contains...?to support simultaneous master and slave connections will it need any firmware update...?
...
As we known we can set static passkey in peripheral side (s110) with the API sd_ble_opt_set(BLE_GAP_OPT_PASSKEY, &ble_opt) as below:
inline void setPassKey(void)
{
uint8_t...
I've tried all 4 versions of the HID Mouse Example provided through the Keil Pack Installer tool and can't seem to get any of them working.
The code compiles and downloads...
I was trying to compile the example code(nRF51 SDK8.0) for ANT and flash to my nRF51DK(pca10028) board, but the example code was not working on my board. I tried compiling...
Hello.
I'm now writing a software based on nrf51_sdk_v6_1_0/nrf51822/Board/nrf6310/s110/ble_app_hrs. The SoftDevice I'm using is s110_nrf51822_7.1.0_softdevice.hex. Why...
So I've been using a user submitted SD safe TWI implementation that I found here. This has worked well so far, but upon updating to SDK 8.0.0 parts have broken. Now when I...
Hi,
I'm using the NRF51DK which comes with the nFR51422. I initially flashed the board using the ble_uart example.
Since then I've tried flashing it with other examples...
Since we have some performance problems with sd110 V7.0.0, we tried a upgrade to v8.0.0.
This version(8.0.0) with IC revision 3 solved our performance problems:).
But a...
Hi,
I am working on a project regarding a portable device for healthcare monitoring. This device will have a nrf8001 module integrated that will communicate with a iOS...
Hello there,
I know that the range of the possible BLE communication depends on the internal configuration as well as on the external environmental conditions.
I would...
I downloaded the zip file from Git Hub Nordic.. and extracted it into C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\7.1.0\ble_peripheral\
When I open the project...
Hi~
I have a nrf51822 EK board(PCA10001 V2.2.0), but the J-link OB can't flash 51822 chip.
The situation is:
1.I can see Segger J-link on segger software&nrfgo studio...
Hi all,
I've been trying to get a new Win 7 (x64) PC setup with with the Nordic dev tools.
Studio, MCP, SDK etc.
I've installed Studio (1.17.1) and MCP (3.7.1). This...
Hi...
i have downloaded latest SDK zip file "nRF51_SDK_7.2.0_cf547b5.zip" from developer.nordicsemi.com/.../ but i could find mdk file "nRF51_mdk_6_1_0_installer" only...
