Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi, CAn anyone plz help me getting the cheapest possible nrf51822 small module that i can use in my project as peripheral ?
Or any other module that can work as slave with...
Hello,
I have been able to get an application to build and run in debug mode using Eclipse GCC (Kepler) for the nRF51822. My application does not use a soft device. We...
Hello,
I want to use timer with my app. I want to make led on my beacon flash for 1 second when it recieves a value. How can i set timer to turn of led after 1 sec?
...
Hi,
I am using GPIOTE interrupts to detect button presses. It works fine but there are only four channels in GPIOTE->EVENTS_IN[] and each channel can only be assigned to...
Hello,
I'm using exeprimental dual mode example with my Beacon kit. I ported the example to work with pca2006, but i'm having problems with led. On my mkit, leds work just...
This is what happens when linking my project in Eclipse:
make all
'Building target: project_name.elf'
'Invoking: Cross ARM C Linker'
arm-none-eabi-gcc -mcpu=cortex...
Hello,
We would like our app to only be seen by:
Devices that have previously connected
Devices that we allow to be added to the whitelist via the temporary disabling...
In my pursuit to make a stable Gazell streaming device, I noticed some issues with pushing packets to the Tx FIFO.
Even through I get an affirmative response from the nrf_gzll_ok_to_add_packet_to_tx_fifo...
Hello,
After I connect my iPhone with a 8001 nordic chip without opening the characteristic I receive a pipe status event which says that the pipe is opened. This is totally...
Hi,
I would like to use the softdevice s130 because i want to try having a nrf58122 as a ble central and peripheral at the same time.
At the moment, there is still the...
Hey everyone,
I have an application where I have to write data to a characteristic. I would like to only allow reliable writes (not unacknowledged ones). Is this permitted...
Hello,
I'm having problems with defining RGB led on my beacon (pca20006). When i define for example RED led (on pin 12) with code nrf_gpio_cfg_output(12); i should be able...
Hello,
I am trying to load ble_app_beacon code provided in nordic sdk to redbear lab's ble nano. I am using sdk version 8.0.0 and soft device(s110) version 6.2.1 .
I am...
