Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
whether one s110 device can connect to multiple s120 devices simultaneously...?
if not what is the special feature mentioned in Bluetooth 4.1 specification..?
is it limitation...
I'm testing ble_app_ancs experimental sample.
It seems working first connection. But after rebooting iOS Device, or Turn Off/On bluetooth function on iOS Device, ANCS does...
I'm developing an UART with SD110. I've updated the SDK to the newest 7.1 and I'm using MDK Pack-Installer.
I found a problem in app_uart.c and retarget.c .
retarget...
I have a nRF24L01+ connecting to an Arduino board using the RF24 library code. It is a print of the registers:
On the nRF51822 I have the following code:
int main...
Hi, I was looking on Digikey and there is a device with the following code: NRF51422-QFAA-R7 V2
Does anyone know what the R7 V2 means? I think R=reel? Thanks
Hello everyone,
I have two nRF51822 (PCA10024) which I want to communicate, one is a peripheral s110 and working properly with a batery service and a custom service, and...
I am new to BT certification so my following question may be incorrectly stated.
We are creating a new OEM BLE module using the nRF51882-CFAC. We intend to sell this module...
Devzone,
I've been working on a central device based on the project 'ble_app_multilink_central' and have encountered an error originating from within the softdevice of...
In Bluetooth 4.1 spec they mentioned scatternet option for BR/EDR topology....not for LE topology...
is that option of connecting to multiple centrals at a time will applicable...
I need a BLE device that can broadcast codes/id to my android mobile app. Also, I need those codes be changed by once in a while by an admin app. Is this possible?
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
