We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi,
I'd like to know how can I implement a Scene Server for one or more Generic Onoff Servers (typically leds).
I read the documentation related to Scene Server and I...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
i use demo ble_app_multilink_central and ble_app_multilink_peripheral ,in SDK 8.1.0,but when i use sd_ble_gap_connect (S120 to S110)return NRF_ERROR_INVALID_STATE ,
why?...
I am checking values of my PCB with an nRF51822. VDD = 3V. AVDD ~= 800mV
I was expecting a the AVDD voltage drop to be much less. What should the AVDD voltage be? What...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
We have the bootloader working over serial at UART_BAUDRATE_BAUDRATE_Baud38400. We took a big leap and tried it at UART_BAUDRATE_BAUDRATE_Baud230400 and it failed. We will...
Dfu not working when i try to upload my custom made application second time.
nrf51422 sdk v8.0 and softdevice s110 on pca10028
the steps i used to do dfu are as
1)programed...
Dear all
I have some questions about nRF51822 bluetooth smart beacon kit, I read the User guide, but I can't get information about the following questions:
1、what is the...
I want to change bootloader start address BOOTLOADER_REGION_START to 0x33800 to store user data and DFU. But when I only change BOOTLOADER_REGION_START, my device can't work...
Dear Developerzone Board
Does the nRF51822 Sniffer just start with the conversion over all advertising channels or do I need to send a start command? Which command set...
The ENable pin on addition hardware component requires "floating" to power on, and drive low ( less than 1.25V) to turn off.
Unclear based on my understanding of the chipset...
Hello
Is there a way to stream data from one nRF51 device, to a second nRF51 and have the received data sent over UART to a host PC? Basically in my setup, I have a custom...
I'd like to understand why BLE_GAP_ADV_TYPE_ADV_IND is used while using a whitelist.
An example application that does this is the ble_app_proximity app. You'll see the...
Hi.
I need to use multiple SPI devices and I'm not sure which is the proper way to handle this, should I open/close each time the SPI port with different SS pin configurations...
