I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have a question about using the GPIOs,I found that I can set a ‘1’ at the same bit position of OUTSET register and OUTCLR register. But which one is effective ?
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
Hi,
When erasing one page flash for responding one GATT request, it always went into assert_nrf_callback and has to reset the app. So I have to disable SoftDevice before...
Hello,
I am going to start programming BLE application, and I would like to know which enviroment is best to program it. Are there too many differences between programming...
Hello
According to the documentation the optimal CPU frequency is 16 MHz, Please, could someone tell me if that is correct or not?
Thanks for your help
Hi,
I modified the ble_app_hrs sample application with one custom service which includes, some custom characteristics (128 bit uuid), Now the problem i am facing is, i am...
Hi,
How to implement the passkey authentication, we are using nF51822 evaluation board. Is it possible to display the passkey using master control panel? And, we also don...
Howdy,
In a similar vein to my recent question about production programming....and nothing to do with takign an nRF51822 out for a walk :)
We'll write a simple test...
Hi
Before, TX and RX functions run well at iOS6. After we updated to iOS7, RX still worked but TX couldn't send out data. Did you verify nRF UART app at iOS7?
I'm reseaching a tag in low energy-cost using the nRF24le1.Till now,I can receive the message from the tag successfully, but can't send the command to the tag to read or write...
hi,
Now,my pre-Develop product(BLE),that to measure the Tx transmit power not correct with my setting(default 0dbm).
so,i have program a project for to sure the reason(Hardware...
I need to connect an I2C/TWI device to the nRF51822. The I2C device is running at a fixed 3.3V (from a boost DC/DC), but the nRF51822 is powered directly from a CR2032 battery...
Hi,
Is there anyway to keep the RTC going while in reset, device sw has crasched or in powered off mode or would I need an external RTC for this?
Is there any possibility...
I have two NRF24L01+ devices. My aim is to have one as PTX and the other as PRX replying with ACK_PAYLOAD. It is working with ACK enabled (without payload). However when ACK_PAYLOAD...
