I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm testing new nRF51822 Beacon v1.1.0 dedicated for smart beacon kit (pca20006). I'm using Master Control Panel Android app version 2.0.3 and Nexus 5 with the latest...
No text. It's a really short question.
So this is a simple example:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit << ADC_CONFIG_RES_Pos) |
(ADC_CONFIG_INPSEL_SupplyOneThirdPrescaling...
Hello, I've just purchased an nRF51 DK and installed the SDK. I have Keil uVision 5 installed from a previous project, with a "Freescale Only" license key. This seems to be...
When i google for power consumption 433mhz 2,4ghz and similar most results tell me that 433MHz consumes less power... but when I look at specifications of explicit chips/modules...
I am trying to do a simple UART test with nRF51822 without BLE functionality. The code is a simplified version of the UART example in nRF51 SDK, and can be found here . It...
Hi,
I just wanted to try out the DFU on the Android app to see if I can successfully update the application on the beacon. For that, I only uploaded the precompiled nrf51822_beacon_app...
Using Blend Micro (Arduino Uno + nRF8001) to gather environmental sensor data and send to mobile via notifications. Here's my main loop:
void loop()
{
aci_loop();
...
Hello,
I know I have seen the topic on the forum, but can not find it. What changes need to be done to a example project designed for a softdevice 110 to convert it to...
The s310_nrf51422 migration document states:
Due to an issue present in this release, the application is required to set the device address to the factory default right...
Hi,
I was just wondering what the sequence of events would be in the following scenario:
A S110 peripheral device (GATT server) has a characteristic with write access...
Hi all,
I've spent 4 days now (!!) on getting a "Hello World" project to work in eclipse with GCC. I guess something around the startup-code is setup wrong in my very simple...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
