Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi,
I am looking for suggestions in regards to which ble example I should use. Currently, I have the hardware that writes data to a flash. I am developing the firmware...
There are several tickets from users trying to get the combination of Zephyr and Segger Embedded Studio (SES) to work on Mac OS including Catalina, but some are unresolved...
Hi,
I want to do an DFU OTA in nRF52840 BLE chip.
I have flashed mcuboot bootloader and also flashed hci_uart (To scan BLE beacons) application. This will be one time...
Hello to all,
I have a problem relating to cluster reporting: I have a device, Window Covering Device, which acts as a router and I want to connect it to Alexa, which acts...
Hello, guys.
Here they are - Thingy:91 and nRF9160-DK boards on my desk!
I was able to successfully register Thingy:91 on nRF Cloud (both SIM card + LTE modem). However...
Hello All,
I was reading about the startup code and vector table of Cortex-M4 (STm32, Tm4c123). When I tried to find out the Vector table of NRF52832 in the datasheet I...
Hi,
This is my second post about this issue, but I have not solved yet. The issue is, that I am using bpwr tx example (crank torque sensor type) with Garmin edge 520plus...
I am developing an android app which is connecting with this product. In that particular case my app advertises, the nRF scans and initiates connection with my app. Some phones...
Hi Nordics,
we would like our central nRF52840 to have DFU timeout in 20 seconds , if no connection received via nRFconnect phoneAPP to perform the firmware udpate, then...
Hi Team,
I have a some query regarding nordic mesh
I would like to know that Nordic mesh is compatible with CSR mesh ?
Does nordic mesh is compatible with any 3rd...
Dear: Addressee
Hello!
I have a question about the program development of Bluetooth chip.
There is no client program for blood pressure measurement in SDK (15.2.0...
To do a serial DFU I have followed the steps provided in the DFUMaster_UART link.
1) Generated the key using the NrfUtil.
2) Added the private.key and generated a DFU...
Hi,
I try to flash application + softdevice + bootloader into the nrf52810 with following commands but it does not work? Can you look into this?
nrfjprog --program...
Hi,
We are developing central scanning mode for our project requirement. We want to scan BLE tags which are transmitting at every 10 seconds. I have been using nRF52833...
