Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi, Is there a UART bootloader built in to the factory firmaware similar to others like NXP LPC series where a specific pin is held low at reset. If so what pins are used...
Hi, Nordic Engineers:
Pls give your hand, new question: Could i run two app on one mobile-phone that connceted with only one device? also, they can operate the device by...
Guys, I would like to put the internal uC in sleeping mode while nRF51822 is advertising and wakeup him, when I establish a connection.
I know that is possible, it must...
Alright, so I am having a lot of trouble generating a valid zip file to update with nRF Toolbox (android).
I used nRFgo Studio to flash dfu_test_app_hrm.hex and dfu_test_bootloader_b...
I got a Tablet running Windows 8.1 with a Bluetooth Module that is able to find my nRF51-DK.
Is there a software I can use to interact with my Bluetooth Services of the...
I am currently developing an IoT device using nRF8001 which needs to report gas concentration obtained from a sensor. I have looked through the standard GATT profiles , and...
Hi,
I am having trouble understanding the new PACK structure in a project, in particular, with the example project dfu_dual_bank_ble_s110_pca10028.uvprojx.
My setup...
Hi,
I would like to know what is the footprint of softdevice S110 v8.0.0.
When i compile the Glucose code example from Nordic it shows a Program Memory utilised as around...
According to the device manager the length in bytes returned by sd_ble_gatts_sys_attr_get() is:
((ATTR_SIZE * (CCCD_COUNT + 1) + CRC) * 4)
When I call sd_ble_gatts_sys_attr_get...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi
I am trying to change the radio's transmit power in program, but I can't solve it.
I downloaded nRF51822 Beacon v1.1.0. and am testing PCA20006. (Source Code\nrf51_beacon...
Hello,
for my sensor I need to have a delay BEFORE pulling CS high. So I would like to add an argument to the
spi_master_send_recv()
function that give me exactly...
Hello,
I am altering this project: nRF51_SDK_8.0.0_5fc2c3a\examples\ble_peripheral\ble_app_hrs\pca10028
I am trying to turn on the BSP UART. I main.c the project uses...
