Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi, I programmed my nrf51dk with ble_app_beacon and I see a blink every two seconds on the board's led. I started the nrf Beacon app in my iphone 6. I first added a beacon...
I have two questions:
Question 1 :
What is the timer timeout limit on nRF51822?
The reason I ask is that I want to update the advertising packet periodically. Below...
Hi,
Here is the issue details.
I have my application loaded on the nRF51822 controller and it acts as a peripheral. The IOS device acts as a central.
The connection...
I am new to chip testing and need some advice on how to start. I am trying to test a nRF51822 on a custom PCB. The main elements of the PCB are the nRF51, a GPS module, and...
Hello,
I try to perform an pstorage store action after I'm done advertising just beform the devices goes in system OFF mode. Pstorage works fine before I start advertising...
I've gotten two PCA10001 boards working with the LED_mesh sample.
I cannot get the third board to run BLE_Gateway (it does not react to button presses, nor is it discoverable...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear all,
I'm not able yet to start advertising with whitelist whith this code:
void AdvInit(void)
{
ble_advdata_t advdata;
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED;...
I have a nRF51 DK board and its flashed with the SD 110
I want to have a timer which will interrupt every 50us.
This is how I set up the timer:
#define APP_TIMER_PRESCALER...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi
I'm using nrf51422 to send periodically a frame through ble_nus service to the Nordic nRF UART app. One of the frame data is the message count number, that is reset...
