Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Dear All, I would like to know which is the better GPIO configuration to drive a LED for extremely low power consumption. We have a board with nRF52832 SoC with GPIO connected...
Hi,
I have Android (8.1.0), and installed nRF toolbox 2.8.0. To update firmware using .zip file.
The DFU Upload returns error:
Unfortunately, nRF Toolbox has stopped...
The 3GPP Release 14 introduced new, third power class of 14 dBm for NB-IoT devices. Is it possible to assign nRF9160 to operate at the lowest power rating class, the 14 dBm...
Hello everyone,
I am working on a project where I need to interface an NFC reader (trf7970a from TI) to an NRF52840.
I got everything working fine, but I have a major...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
I've created read onle characteristic called "log". In main.c i try to update it by calling : ulogd_characteristic_update(&m_ulog_service,Log_Data_arr)
But nothing happens...
How can delete individual peer bonding data without to affect the rest bonds:
-currently connected (after disconnect)
- some peer by providing RPA (assuming RPA matches...
Hi,
Is it possible to enable the transmission of 2 bytes of preamble and use the TIFS register to force a delay to transmission when in proprietary 2Mbps mode?
Thanks...
Hello, I'm using SDK 16.0, softdevice s132 v7.0.1, I'm sending the device to SystemOFF and configuring a pin to wake it up with
nrf_gpio_cfg_sense_set( IMU_INT2_PIN , NRF_GPIO_PIN_SENSE_HIGH...
Hi,
I am using a 52832 part as a peripheral communicating with a central running on an ESP32. It operates in the following manner:
1. When it is active, the peripheral...
I am getting a "Stopped by vector catch". This isn't particularly informative. How does one find the code location where the fault is generated?
Thanks
Hello everyone,
I just started learning BLE. I want to develop an application that gets RSSI from a beacon and displays the magnitude of RSSI using 4 built-in LEDs.
Beacon...
We want realize mesh network to mibile phone clients using BLE5
We assume we are have to use 3 types of devices:
1) Mobile phone/pad with built-in BLE5
2) Access points...
In our use case we are using the nRF9160 in eDRX mode with an eDRX interval of 40.96sec.
I'm noticing that the power required to transmit a message varies widely between...
