Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I could use some clarity on the legacy drivers/files, nrf,driving example applications inside SDK 16. Is it just too much work to clean up the examples with current drivers...
Hello everyone,
I am trying to implement UARTE on a custom board embedding an nRF52832 , as part of an upgrade from SDK 12 to SDK 15 . The nRF52832 is communicating via...
Hi,
A new modem firmware for nRF9160 has been released. Is it safe to update the modem firmware of Thingy: 91 to v1.1.1? We can download the firmware from nRF9160 SiP page...
Hi,
I'm trying to merge Serial and BLE DFU. I have followed this .
I have used BLE DFU example as base code and added Serial DFU dependencies.
I'm able to do BLE DFU...
HI,
i have made 3 customer board
they all use the same spi flash mx25v8006e
and the first two board have the spi pin : sck 3, miso 1,mosi 0,ss 2
but i change the design...
All I want to do is use the "Advertiser" tab in my nRF Connect android app and force it to broadcast using a custom 128-bit UUID.
I am struggling to figure out how to do...
I have tried combining a working SDK16_98a08e2 MPU6050 example with the SDCard example in the same SDK, however it seems they are incompatible because the MPU example uses...
Hi,
I am developing a device with nrf52840 soc, I need to know that there is any unique and unforgettable id in this chip that with that I could differentiate between...
Hi, Just wanted to pass this along... with the latest Raspbian (09/26/19) the thingy52 will consistently disconnect after about 90 seconds (+/- a few seconds). You can easily...
Hello,
I have two boards of nRF52840, one being central and the other is peripheral. On the central I've put the code from ble_app_multilink_central and on the peripheral...
Hello,
I see this type of query or GATT error has been asking continuously. I have gone through all the same Q&A but not able to solve my query. I have tried all the possible...
Hello Nordic support,
I was referring to the RTC example in nrf52 SDK where an interrupt is triggered on Compare Counter event. In the example, the interrupt is triggered...
I am trying to make custom BLE service to send the data from one nRF52832 to another nRF52832 but we followed the below tutorial "Bluetooth low energy Advertising, a beginner...
Hello,
We are developing a device that needs to get local binding info on init to see if it needs to send data or not to an on/off server in a remote device.
Is there...
