Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
I was unaware that the 'manufacturer data' in the advertising packets is limited to less than a full payload. However, whenever I set it to >6 the program "crashes".
...
When I use keil to download the software to the chip, there are two questions:
like attached.
2.NRFGO CAN'T SEE J-LINK LITE CORTEXM BOARD
Is there any way to solve...
We have recently moved to a new PCB which puts the nRF8001 on the layout instead of plugging into a nRF2741 development module. The nRF8001 connects to a TI Cortex-M4 Tiva...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
To be more detailed:
One of my ADC pins will be connected to another device that could be providing a voltage of about 3V, but through a 100 kohm resistor. (actually it...
Dear Nordic Developer Zone,
Since I have implemented a timer with interrupt in my application, the debug mode if the Keil IDE stops working when I try to restart the code...
Hello, I'm trying to develop with the nRF51822 Eval kit and GCC and Eclipse. I've been getting some strange behavior and errors lately. I'm not really sure how to describe...
I'm a green hand HW Engineer.
I'm trying to compile, program, and run The Heart rate monitor demo though following the step in nRF51822_DK_User_Guide_v1.0.pdf .
First...
Hi Nordic devzone,
For the nRF51822 device, I would like to know if there is any internal pull-up/pulldown resistor on SWDIO and on SWDCLK (although a 12 K-ohm pulldown...
Is it possible through the API/Softdevice to do one of the following:
read out the current advertising data structure, change a the manufacturing data field, and...
Hi,
I am planning to use modules with nRF8002 in an indoor positioning application.
The mobile devices that are to be located are continuously scanning for BLE devices and...
Hi, got an interesting problem, this is on a custom board with nRF51822 QFAB that we are bringing up. The radio test (not using softdevice) works ok and produces strong transmit...
Hi
Could you provide the power current in System on Active, System on Sleep, and System OFF for nRFready Desktop2 keyboard and mouse? nRF51 was programmed Desktop 2 v1.0...
