I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
So, we have been developing our firmware (for a while now) against a SoftDevice version called 6.0.0-1 alpha. We are getting close to production time, so we wanted to switch...
I had a product working with S110(BLE peripheral).
I am trying to get same BLE feature working on an product working with S210(ANT)
So I chose S310 to have both ANT and...
Hi devzone...
My setup is nrf51422 dk with soft-device S110 on the server side and on the client side i am running MCP 3.8.0 on a PC using usb dongle.
I am using Queued...
1 sensor per nRF51288.
Sensor supports either 400kHz I2C (10k pull up recommended) or SPI (2MHz typ, Max 20 MHz)
From the nRF51288 Product Specification:
Run current...
I want to use the s130 softdevice because we need the broadcaster/observer mode at the same time. I bought the nRF51 Dongle and the beacon Device.I use the Keil IDE, debugging...
From the question "Advertising on a single channel", the new S110 supports advertising on one single channel. What I want to know is if S120 supports listening on one single...
Hi,
Thank you for looking into this issue.
The target BLE module we are using is a custom board (Rigado BMD200) based on nRF51822 s110 chip. We have tried a few example...
Hi,
I am following the tutorial using Raspberry Pi Kernel version 3.18, but after the step 7, the raspberry gets frozen with the colorful image in the beginning of the boot...
Hello,
we want to establish a UART communication between the Dynastream N548M8CB Module and a TI Mikrocontroller. I have tested the UART loopback example with the pca10028...
In the data sheet of SHT21 is this the formula to calculate the temperature:
T = -46.85 + 175.72 * temp_data / 2^16
temp_data has the value 26'464.
The result should...
Hi,
I'm trying to define a new service, and on the GAP settings, I would like to advertise my service, but I get an error message: advertisement packet too long.
What...
I have a temperature/humidity sensor from Sensirion. The Type is SHT21x. The sensor has I2C so it should be able to tranfer the data from the sensor to the Nordic chip over...
Hi,
I am attempting to get the ble_app_beacon example working with the s130 softdevice instead of the s110. I am using armgcc and the v8 sdk softdevice headers on a pca10031...
