I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
Hi: I use dfu_single_bank_hci to update application. HCI_SLIP_UART_MODE = APP_UART_FLOW_CONTROL_DISABLED, HCI_SLIP_UART_BAUDRATE = 38400.
I use command " E:\hci_dfu_send_hex...
Hello,
In my quest of working with pstorage_raw.c I found an annoying situation when I tried to clear small portions (as I thought by using raw I would have full control...
Hello!
I have based myself on the ble_app_uart example, taken out the UART bit, and all that remains is the bluetooth functionality.
I have also implemented SPI communication...
hi guys, :)
I used SDK 6.1.0., Softdevice version is S110_nRF51822_7.0.0.
I compiled the template project. (in the "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310...
I want to use the UART to get and send data to another MCU on ble_app_beacon of SDK 8.1.0.
But after I add the UART function to the project, the UART can't work.
Can the...
Thanks for the SDK 8.1.1 fix. Please make it available also as a .zip in developer.nordicsemi.com/.../
Currently the fix cannot be used with a GCC toolchain as it is only...
Hi,my friend
I use the nrf905,At one end Use the PCB antenna, on the outside part of the metal.Using the results, said communication distance is shorter than 40 meters, easy...
Hi,my friend,
I have been using nrf905, but its performance is very bad.
Have a compatible chip nrf905 data communications? Working frequency 433 MHZ,100 KBPS baud rate...
uart_fsm and proc_fsm never get called.
debug on the first line of the uart_fsm and proc_fsm are do not come even
gpio toggling stops once uart interrupt received. I am...
Hi there,
I'm trying to build the Beacon source code with GCC toolchain on Ubuntu, but it's not working on Beacon Kit, there is no any response from the kit. But I tried...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi,
I'm trying to see what the communication range would be for different transmission powers. I set the transmission power to 0 dBm, and observe that I can still receive...
