Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hello Guys,
I am interested in what is the packet size of Heart Rate application board example included in nRF51 SDK 6.0. I am using nRF51822 Evaluation board. Could help...
I am working on nrf24l01+ which interfaced with atmega32. I received data but it take time to receive (appx. 1min). I set RF_SETUP to 0x27 ,disabling auto ack and sending...
I consider to use a 32k MEMS oscillator instead of a usual 32k quartz crystal with a nRF51822 (WLCS). 32k MEMS oscillator's package is quite small 1.55 x 0.85 mm, there's...
I am developing on a custom board using nrf51822 with pure gcc. The blinky makefile worked fine. Before going to ble_hrs makefile, I want to load the blinky_example with softdevice...
hi guys,
i've a general question about bluetooth (general usage of characteristics), and i hope somebody could give me a hint how to use them properly.
So, i want to communicate...
Hello.
I've tried linking the ESB library in IAR but I am still getting error.
When link arm_lib.lib getting this error:
Fatal Error[Li014]: error when reading "nrf_esb...
I'm attempting to use the Master Emulator API (2.1.8.8331) with a PCA10000 on Windows 8.1. I'm just creating an instance of the MasterEmulator and I receive a PythonException...
Hi, I'm using an nRF8001 with a locally stored GATT service and security enabled.
I have already established a bond with a master device. The master has enabled notifications...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi!
I was trying to program bootloader provided with nRF51822-DK using nRFgo studio but I receive error like attached:
I was also trying to follow this guide:
...
I want to add an external PA to the NRF51422. My understanding of 15.247 is that you can transmit up to 30dBm if you use spread spectrum. Does the NRF51422 use DSSS for Bluetooth...
When is the most appropriate time to set the transmit power while using the S120 softdevice? I want to set it once at power up. Most examples that use the S110 SD set the...
Suppose I want my BT peripheral to provide Measured value of sensor X and Location of sensor.
Currently I have to send the following attributes
Service Attrinbute
Characteristic...
Hi All,
I am working a custom board for 51822. We have wired the UART RX/TX pins to a microusb connector (No RXD/TXD pins wired). The problem is once we connect it to PC...
