Hi, I've been given an nRF52 devkit and have been tasked with programming to generate a 2.4GHz signal. The requirement given to me is that simple. (I believe an RF expert...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hi, I have written some code following an example for my nRF51-DK using a sensor and HeartRateService, but I tried to use some apps and the scan doesn't seem to see my phone...
Hi.
I have a custom board based on the nRF51822. Application uses s130, SDK 11.0.0. It's a peripheral. Using gcc.
I'm finding that when field testing my device, it will...
Hello,
I'm trying to measure the time difference between two pulses using GPIOTE, PPI and a Timer.
My platform is:
nRF52832
SoftDevice S132 v2.0
My thinking is to...
without timer it work fine but when i use timer it goes here.
my timer code is this
#define APP_TIMER_PRESCALER 0 /**< Value of the RTC1 PRESCALER register. */
#define...
Hi,
I am following the user guide nRF51822 Evaluation Kit User Guide v1.2 , the heart rate monitor demo, Scaning for available Bluetooth low energy devices:
I started the...
Hi,
i am working on a custom board with nRF51422. I can program this board with the nRF51-DK. I use ADC and a temperature sensor via I2C. Everything work well but actually...
I am using nrf_toolbox on Windows Phone 8.1 and PCA10040 development board. I loaded the uart example and with my phone I can send text via nrf_toolbox. But when I want to...
Im' trying to send a set of 80 bytes using indication. for that I have a characteristic sending each time 20 bytes and wait for indication acknowledgement before sending the...
Hello Nordic! My application requires an nRF51822 using S110 to handle both Notifications and Indications over the same characteristic.
The CCCD value 0x01 = 0b01 enables...
Hi,
In order to start my own board with nRF52 component throught SWD, I think I've to use Segger Jlink. I expect to buy the basic version, that sound good for me, but I...
Hi,
I have some problems with bootloader debugging by using app_trace_log().
My board is pca10028, and I use the SDK 10.0.0 for it. The Keil version is v5.20 and Jlink...
Hello All,
How to interface nRF905 with nRF51DK board?
Any driver is available for nRF905 which support nRF51.
Any help will be appreciated.
Regards,
Rajneesh
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
